Ersatzteil BK20-24V/DPE09XB4C-TF-G-FV/SP Bauer Gear Motor

Informationen zum Ersatzteil BK20-24V/DPE09XB4C-TF-G-FV/SP

The motor offered by us, in today's list IE3 execution, has identical mechanical connection dimensions as the type you requested. Please note: The motor part is 58mm longer than shown on the supplied dimensional drawing. Motor power: 2,2 kW Speed of the AW: 125 r/min Installation: H1 Terminal box position: II / A Corrosion protection: Standard Painting: RAL 7031 Dimension drawing: BK20-BK20Z Catalog: B 2010 Net weight per piece: approx. 52 kg Suitable for operation on static converter in frequency range: 5 - 50 - 87 - 100 Hz Voltage: 37 - 230 - 400 - 400 V D power: 0,225 - 2,2 - 3,85 - 4,45 kW synchronous speed: 12,5 - 128 - 220 - 255 r/min load torque: 143 - 155 - 155 Nm load current approx.: 8,7 A service factor: 1,5 Gearbox design: Type: BK20 2 -step bevel gearbox design code number 24V with small flange on front side (d: 200 mm) hollow shaft with keyway (d: 30 mm) Total reduction i: 11,69 Additional/special versions: Closing cap on gearbox side H Lubricant grade: PGLP 460 With Heinrichs venting. Motor design: Type: Three-phase squirrel-cage motor DPE09XB4C-TF- G-FV Rated speed: 1450 r/min Voltage: 230 V Stator circuit: D frequency: 50 Hz Rated current: 8,0 A Power factor cos phi: 0,80 Efficiency: IE3 - 86,8 % (according to EN 60034-2-1) Thermal class: F IP protection class according to EN 60529: IP 65 IC cooling type according to EN 60034-6: IC 416 Terminal box: TB222R Design according to DIN VDE 0530-1/EN 60034-1 Additional/special versions: With built-in thermistors for switch-off according to additional connection diagram ZK010.1040-14. With attached forced cooling fan in wide voltage version Connection 3 phase 200 - 303 V; 346 - 525 V; 50 Hz Connection 3 phase 220 - 332 V; 380 - 575 V; 60 Hz Connection 1 phase 220 - 277 V; 50 Hz, 60 Hz With mounted incremental encoder Type: EIL580 Pulse frequency (imp/rev): 2048 Supply voltage DC: 8..30 V HTL Output signals: A;B;N+Inv Current consumption: max. 70 mA IP protection class according to EN 60 529: IP 65 EIL-Tacho connected via cable to additional terminal box Please note: Gearbox With regard to radial alignment tolerances, the following must be observed with the the flange of the gearbox version "hollow shaft and flange the flange must be cleared so that centering via the bearings is possible. via the bearings is possible. This largely avoids indeterminable bearing forces. avoided. However, this measure cannot compensate for angular errors. For gear units with torque support by means of a flange or a torque support, the side of the side of the torque support must be on the side of the transverse force via the work shaft! Deviating designs must be consulted at the factory. Motor Motor connection via CAGE CLAMP (cage clamp technology)! CAGE CLAMP is a registered trademark of the WAGO company. The operation with increased input speed leads to increased operating operating noise and increased increased heating of the drive. Operation at an increased input speed reduces the service life of the service life of the shaft seals, which must be taken into account when scheduling the service intervals. be taken into account. Please check whether the assignment of voltage and frequency for motor and inverter match. Forced cooling fan When operating with different frequencies (frequency hopping, inverter operation), the forced cooling fan must be supplied from a separate mains mains (possibly control mains).